November 26, 2016
Orange Pi PC 2 - first boot with Ubuntu
I put the Ubuntu "server" image on an SD card
plugged it in, and connected power.
This is the output captured on the serial console:
Once it boots, I login as root with password "orangepi".
HELLO! BOOT0 is starting!
boot0 commit : 8
boot0 version : 4.0
set pll start
set pll end
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
DRAM BOOT DRIVE INFO: V0.6
the chip id is 0x00000001
the chip id is 0x00000001
the chip id is 0x00000001
the chip id is 0x00000001
the chip id is 0x00000001
axp not exist
DRAM CLK =672 MHZ
DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM zq value: 0x003b3bf9
DRAM SIZE =1024 M
DRAM simple test OK.
dram size =1024
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2016-03-15 20:40
[mmc]: sdc0 spd mode error, 2
[mmc]: Wrong media type 0x00000000
[mmc]: ***Try SD card 0***
[mmc]: HSSDR52/SDR25 4 bit
[mmc]: 50000000 Hz
[mmc]: 7580 MB
[mmc]: ***SD/MMC 0 init OK!!!***
sum=710a857c
src_sum=710a857c
read boot-pkg from emmc 32800 sector
Succeed in loading uboot from sdmmc flash.
Entry_name = u-boot
Entry_name = monitor
Entry_name = scp
set arisc reset to de-assert state
Ready to disable icache.
�INFO: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):3ffd944
NOTICE: BL3-1: Built : 11:09:10, Aug 30 2016
NOTICE: BL3-1 commit: 3ffd9442d4769d7fc0002770e3b69b55150a288e
INFO: BL3-1: Initializing runtime services
ERROR: Error initializing runtime service tspd_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x4a000000
INFO: BL3-1: Next image spsr = 0x1d3
U-Boot 2014.07 (Nov 09 2016 - 15:49:10) Allwinner Technology
uboot commit : 8
secure enable bit: 0
i2c: secure monitor exist
[ 0.742]pmbus: ready
u0:48105000
[ 0.746][ARISC] :arisc initialize
[ 0.776][ARISC] :arisc para ok
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :arisc version: [sun8iw5_v0.03.00-244-gb750b8e]
[SCP] :sunxi-arisc driver v1.20 is starting
[ 0.792][ARISC] :sunxi-arisc driver startup succeeded
axp: get node[charger0] error
[SCP ERROR] :message process error
[SCP ERROR] :message addr : 48105080
[SCP ERROR] :message state : 5
[SCP ERROR] :message attr : 2
[SCP ERROR] :message type : 80
[SCP ERROR] :message result : f3
[SCP WARING] :callback not install
[SCP ERROR] :arisc twi read pmu reg 0x3 err
probe axp806 failed
axp_probe error
[ 0.973]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz MBus=400Mhz
run key detect
no key found
no uart input
DRAM: 1 GiB
fdt addr: 0x76e9f0e0
Relocation Offset is: 35ef2000
axp: get node[charger0] error
In: serial
Out: serial
Err: serial
gic: sec monitor mode
[box standby] read rtc = 0x0
[box standby] start_type = 0x1
[box standby] to kernel
boot_init_gpio used
ir boot recovery not used
workmode = 0,storage type = 1
[ 1.177]MMC: 0
[mmc]: mmc driver ver 2016-05-20 17:18:00-test0
[mmc]: get card2_boot_para:sdc_ex_dly_used 0
[mmc]: no mmc-hs400-1_8v!
[mmc]: no mmc-hs200-1_8v!
[mmc]: no mmc-ddr-1_8v!
[mmc]: delete max-frequency from dtb
SUNXI SD/MMC: 0
[mmc]: 50 MHz...
[mmc]: sample: 63 - 158(ps)
[mmc]: 100 MHz...
[mmc]: sample: 32 - 156(ps)
[mmc]: 200 MHz...
[mmc]: sample: 16 - 156(ps)
[mmc]: media type 0x0
[mmc]: Wrong media type 0x0
[mmc]: ************Try SD card 0************
[mmc]: host caps: 0x27
[mmc]: MID 03 PSN b9a71076
[mmc]: PNM SL08G -- 0x53-4c-30-38-47
[mmc]: PRV 8.0
[mmc]: MDT m-8 y-2016
[mmc]: speed mode : HSSDR52/SDR25
[mmc]: clock : 50000000 Hz
[mmc]: bus_width : 4 bit
[mmc]: user capacity : 7580 MB
[mmc]: ************SD/MMC 0 init OK!!!************
[mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
[mmc]: secure_feature : 0x0
[mmc]: secure_removal_type : 0x0
[ 1.394]sunxi flash init ok
[ 1.409]start
drv_disp_init
tv_init:
tv_probe:000
no report hpd work,you need support the switch class!
screen 0 don't support TV!
tv_init:
fetch tv1 err.
drv_disp_init finish
hdcp is closed by sys config.
no the part:Reserve0
hpd_dev_num=2, id of def_output_dev is 0
hdmi hpd out, force open?
fdt_setprop_u32 disp.init_disp(0x20b0404) code:
fb_id=0, size=3686400, gd->ram_size=1073741824, SUNXI_DISPLAY_FRAME_BUFFER_SIZE=16777216
[ 1.981]end
PowerBus = 0( 2:vBus 3:acBus other: not exist)
no battery, limit to dc
no battery exist
sunxi_bmp_logo_display
[boot disp] can not find the partition Reserve0
bmp_name=bootlogo.bmp
** Bad device size - sunxi_flash 0 **
sunxi bmp info error : unable to open logo file bootlogo.bmp
fail to find part named env
Using default environment
--------fastboot partitions--------
mbr not exist
base bootcmd=run mmcbootcmd
bootcmd set setargs_mmc
no misc partition is found
to be run cmd=run mmcbootcmd
cann't get the boot_base from the env
read item0 copy0
Item0 (Map) magic is bad
the secure storage item0 copy0 is bad
read item0 copy1
Item0 (Map) magic is bad
the secure storage item0 copy0 == copy1, the data is good
the secure storage map is empty
check user data form private
the private part isn't exist
update dtb dram start
update dtb dram end
serial is: 44005035c120103e078c
[ 2.149]inter uboot shell
Hit any key to stop autoboot: 0
Loading orangepi uEnv.txt from 40000000 ...
reading uEnv.txt
[mmc]: blkcnt should not be 0
140 bytes read in 3 ms (44.9 KiB/s)
Loading boot environment ...
Loading orangepi bootscript ...
reading boot.scr
** Unable to read file boot.scr **
Booting with defaults ...
Loading orangepi orangepi/OrangePiH5orangepi.dtb from 44000000 ...
reading orangepi/OrangePiH5orangepi.dtb
73312 bytes read in 8 ms (8.7 MiB/s)
Loading orangepi orangepi/uImage from 4007ffc0 ...
reading orangepi/uImage
12200584 bytes read in 522 ms (22.3 MiB/s)
reading initrd.img
1090786 bytes read in 49 ms (21.2 MiB/s)
Loading orangepi initrd.img from 44300000 ...
bootm kernel:4007ffc0 initrd:44300000 ...
bootm initd_size:10a4e2 fdt_addr:44000000 ...
## Booting kernel from Legacy Image at 4007ffc0 ...
Image Name: OrangePiH5
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 12200520 Bytes = 11.6 MiB
Load Address: 40080000
Entry Point: 40080000
Verifying Checksum ... OK
XIP Kernel Image ... OK
reserving fdt memory region: addr=40020000 size=800
reserving fdt memory region: addr=48000000 size=1000000
reserving fdt memory region: addr=48100000 size=4000
reserving fdt memory region: addr=48104000 size=1000
reserving fdt memory region: addr=48105000 size=1000
Loading Ramdisk to 76d85000, end 76e8f4e2 ... OK
Using Device Tree in place at 44000000, end 44015dbf
Starting kernel ...
INFO: BL3-1: Next image address = 0x40080000
INFO: BL3-1: Next image spsr = 0x3c5
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.65 (orange@orange-All-Series) (gcc version 4.9.3 20150113 (prerelease) (Linaro GCC 4.9-2015.01-3) ) #55 SMP PREEMPT Fri Nov 18 16:17:28 CST 2016
[ 0.000000] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000] Machine: sun50iw2
[ 0.000000] cma: CMA: reserved 16 MiB at 7f000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc03ef95000 s20224 r8192 d20736 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258560
[ 0.000000] Kernel command line: console=tty0 console=ttyS0,115200n8 no_console_suspend earlycon=uart,mmio32,0x01c28000 mac_addr=96:62:08:fb:22:8a root=/dev/mmcblk0p2 ro rootwait
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Memory: 1024MB = 1024MB total
[ 0.000000] Memory: 985196k/985196k available, 63380k reserved
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB)
[ 0.000000] vmemmap : 0xffffffbc00e00000 - 0xffffffbc01c00000 ( 14 MB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc040000000 ( 1024 MB)
[ 0.000000] .init : 0xffffffc000ad0000 - 0xffffffc000b59f00 ( 552 kB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000acf6f4 ( 10558 kB)
[ 0.000000] .data : 0xffffffc000b5a000 - 0xffffffc000c22a48 ( 803 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (virt).
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 4.241710] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 4.241743] pid_max: default: 32768 minimum: 301
[ 4.242223] Security Framework initialized
[ 4.242248] SELinux: Initializing.
[ 4.242621] Mount-cache hash table entries: 256
[ 4.244619] Initializing cgroup subsys debug
[ 4.244641] Initializing cgroup subsys freezer
[ 4.244854] ftrace: allocating 28417 entries in 112 pages
[ 4.280153] CPU0: update cpu_power 1024
[ 4.280188] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 4.281914] virtual base = 0xffffff800000a000.
[ 4.281941] gicd_base = 0xffffff800000c000.
[ 4.281955] gicc_base = 0xffffff800000e000.
[ 4.283887] CPU1: Booted secondary processor
[ 4.283911] CPU1: update cpu_power 1024
[ 4.285682] CPU2: Booted secondary processor
[ 4.285695] CPU2: update cpu_power 1024
[ 4.287447] CPU3: Booted secondary processor
[ 4.287458] CPU3: update cpu_power 1024
[ 4.287540] Brought up 4 CPUs
[ 4.287623] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 4.288914] devtmpfs: initialized
[ 4.319376] atomic64 test passed
[ 4.319403] pinctrl core: initialized pinctrl subsystem
[ 4.322209] NET: Registered protocol family 16
[ 4.324754] dump_class_init,839, success
[ 4.325983] vdso: 2 pages (1 code, 1 data) at base ffffffc000b69000
[ 4.326024] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 4.327284] software IO TLB [mem 0x7d000000-0x7d400000] (4MB) mapped at [ffffffc03d000000-ffffffc03d3fffff]
[ 4.328499] DMA: preallocated 256 KiB pool for atomic allocations
[ 4.329169] pll_audio-set_default_rate=24576000 success!
[ 4.329210] pll_video-set_default_rate=297000000 success!
[ 4.329264] pll_ve-set_default_rate=420000000 success!
[ 4.329389] pll_de-set_default_rate=864000000 success!
[ 4.329692] ahb1-set_default_rate=200000000 success!
[ 4.330563] de-set_default_source=pll_de success!
[ 4.330580] de-set_default_rate=432000000 success!
[ 4.330650] tcon0-set_default_source=pll_video success!
[ 4.330740] tve-set_default_source=pll_de success!
[ 4.331040] hdmi-set_default_source=pll_video success!
[ 4.334685] sun50iw2p1-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[ 4.337580] sun50iw2p1-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 4.339652] sunxi hwspinlock vbase:0xffffff800005c000
[ 4.423239] bio: create slab at 0
[ 4.424291] pwm module init!
[ 4.430503] SCSI subsystem initialized
[ 4.431562] usbcore: registered new interface driver usbfs
[ 4.433191] usbcore: registered new interface driver hub
[ 4.433556] usbcore: registered new device driver usb
[ 4.435885] Linux video capture interface: v2.00
[ 4.442649] [ARISC] :sunxi-arisc driver v1.20
[ 4.443574] [ARISC] :sunxi-arisc driver v1.20 startup succeeded
[ 4.444262] Advanced Linux Sound Architecture Driver Initialized.
[ 4.445716] Bluetooth: Core ver 2.16
[ 4.445932] NET: Registered protocol family 31
[ 4.445948] Bluetooth: HCI device and connection manager initialized
[ 4.445991] Bluetooth: HCI socket layer initialized
[ 4.446030] Bluetooth: L2CAP socket layer initialized
[ 4.446101] Bluetooth: SCO socket layer initialized
[ 4.446989] cfg80211: Calling CRDA to update world regulatory domain
[ 4.447799] [pm]aw_pm_init!
[ 4.447902] np name = /soc@01c00000/rtc@01f00000.
[ 4.447920] base = ffffff800006c100, len = 4.
[ 4.447935] pmu name: pmic0 .
[ 4.448014] Warning: can not find np for pmic0.
[ 4.448029] pmu name: pmic1 .
[ 4.448059] Warning: can not find np for pmic1.
[ 4.448146] add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed
[ 4.448166] add_sys_pwr_dm: get ldo name for id: vcc-pl failed
[ 4.448184] add_sys_pwr_dm: axpdummy_ldo6 ldo already alwayson.
[ 4.448216] add_sys_pwr_dm: vcc-pc not sys id.
[ 4.448230] after inited: sys_mask config = 0x4855.
[ 4.448263] Warning: can not find np for dynamic_standby_para.
[ 4.448390] [pm]valid
[ 4.448400] [pm]valid
[ 4.448410] Notice: sun9i & sun8iw5 & sun50i not need support normal standby, change to super standby.
[ 4.448460] [DISP]disp_module_init
[ 4.449329] [DISP] init_disp:0x20b0404
[ 4.449348] [DISP] boot_disp:0x0
[ 4.449857] [DISP] fb_base:0x0
[ 4.453889] [DISP] Fb_copy_boot_fb,line:959:no boot_fb0
[ 4.458830] [DISP]disp_module_init finish
[ 4.459948] sunxi budget cooling probe start !
[ 4.459984] CPU freq cooling register Success
[ 4.460010] CPU hotplug cooling register Success
[ 4.460347] CPU budget cooling register Success
[ 4.462069] input: sunxi-ths as /devices/virtual/input/input0
[ 4.462118] thermal thermal_zone0: failed to read out thermal zone 0
[ 4.462625] Switching to clocksource arch_sys_counter
[ 4.506993] FS-Cache: Loaded
[ 4.507556] CacheFiles: Loaded
[ 4.534634] NET: Registered protocol family 2
[ 4.536169] TCP established hash table entries: 8192 (order: 5, 131072 bytes)
[ 4.536351] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 4.536523] TCP: Hash tables configured (established 8192 bind 8192)
[ 4.537712] TCP: reno registered
[ 4.537731] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 4.537772] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 4.538534] NET: Registered protocol family 1
[ 4.539574] RPC: Registered named UNIX socket transport module.
[ 4.539593] RPC: Registered udp transport module.
[ 4.539608] RPC: Registered tcp transport module.
[ 4.539622] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 4.540581] Unpacking initramfs...
[ 4.587551] Freeing initrd memory: 1064K (ffffffc036d85000 - ffffffc036e8f000)
[ 4.588669] lock super standby defaultly!
[ 4.588699] lookup_scene_lock_name: new scene lock super_standby
[ 4.588716] scene_lock_init name=super_standby
[ 4.588732] scene_lock: super_standby, type 5, count 1
[ 4.589984] audit: initializing netlink socket (disabled)
[ 4.590075] type=2000 audit(0.330:1): initialized
[ 4.595016] FS-Cache: Netfs 'nfs' registered for caching
[ 4.596270] FS-Cache: Netfs 'cifs' registered for caching
[ 4.597180] NTFS driver 2.1.30 [Flags: R/W].
[ 4.597463] fuse init (API version 7.22)
[ 4.598647] msgmni has been set to 1958
[ 4.601254] io scheduler noop registered
[ 4.601277] io scheduler deadline registered
[ 4.601405] io scheduler cfq registered (default)
[ 4.602875] sunxi_bootup_extend_probe: bootup extend state 1
[ 4.602895] bootup extend probe ok
[ 4.603454] failed to get easy_light_used assign
[ 4.603473] failed to get standby led pin assign
[ 4.603526] gpio_pin_1(362) gpio_is_valid
[ 4.603860] gpio_pin_2(20) gpio_is_valid
[ 4.604197] gpio name is PL10, ret = 0
[ 4.604520] gpio name is PA20, ret = 0
[ 4.604971] gpio_init finish with uesd
[ 4.606132] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 4.606164] sw_console_setup()1268 - console setup baud 115200 parity n bits 8, flow n
[ 5.511491] console [ttyS0] enabled
[ 5.516265] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[ 5.523453] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[ 5.532020] misc dump reg init
[ 5.543615] loop: module loaded
[ 5.547126] Get boot type cmd line fail
[ 5.554131] spi spi0: master is unqueued, this is deprecated
[ 5.561059] spi spi1: master is unqueued, this is deprecated
[ 5.569621] tun: Universal TUN/TAP device driver, 1.6
[ 5.575169] tun: (C) 1999-2004 Max Krasnyansky
[ 5.584350] PPP generic driver version 2.4.2
[ 5.589581] PPP BSD Compression module registered
[ 5.594740] PPP Deflate Compression module registered
[ 5.600276] PPP MPPE Compression module registered
[ 5.605530] NET: Registered protocol family 24
[ 5.610447] PPTP driver version 0.8.5
[ 5.614720] hso: drivers/net/usb/hso.c: Option Wireless
[ 5.621038] usbcore: registered new interface driver hso
[ 5.627073] usbcore: registered new interface driver asix
[ 5.633195] usbcore: registered new interface driver ax88179_178a
[ 5.640079] usbcore: registered new interface driver cdc_ether
[ 5.646663] usbcore: registered new interface driver net1080
[ 5.653051] usbcore: registered new interface driver cdc_subset
[ 5.659729] usbcore: registered new interface driver zaurus
[ 5.666073] usbcore: registered new interface driver cdc_ncm
[ 5.672262] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.679682] get ehci0-controller, regulator_io is no nocare
[ 5.685867] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000d183e0, 0x:ffffff8000b36000, irq_no:68
[ 5.699171] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.709099] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1
[ 5.719070] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc00047a564
[ 5.741894] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00
[ 5.749635] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.757073] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.764985] usb usb1: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.773186] usb usb1: Manufacturer: Linux 3.10.65 ehci_hcd
[ 5.779186] usb usb1: SerialNumber: sunxi-ehci
[ 5.785080] hub 1-0:1.0: USB hub found
[ 5.789210] hub 1-0:1.0: 1 port detected
[ 5.793929] get drv_vbus is fail, 84
[ 5.797838] get ehci1-controller, regulator_io is no nocare
[ 5.804001] [sunxi-ehci1]: probe, pdev->name: 1c1b000.ehci1-controller, sunxi_ehci: 0xffffffc000d18660, 0x:ffffff8000b3c000, irq_no:6a
[ 5.817298] sunxi-ehci 1c1b000.ehci1-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.827223] sunxi-ehci 1c1b000.ehci1-controller: new USB bus registered, assigned bus number 2
[ 5.837104] sunxi-ehci 1c1b000.ehci1-controller: irq 106, io mem 0xffffffc00047a564
[ 5.859975] sunxi-ehci 1c1b000.ehci1-controller: USB 0.0 started, EHCI 1.00
[ 5.867705] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.875144] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.883056] usb usb2: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.891283] usb usb2: Manufacturer: Linux 3.10.65 ehci_hcd
[ 5.897284] usb usb2: SerialNumber: sunxi-ehci
[ 5.903078] hub 2-0:1.0: USB hub found
[ 5.907204] hub 2-0:1.0: 1 port detected
[ 5.911930] get drv_vbus is fail, 84
[ 5.915839] get ehci2-controller, regulator_io is no nocare
[ 5.922002] [sunxi-ehci2]: probe, pdev->name: 1c1c000.ehci2-controller, sunxi_ehci: 0xffffffc000d188e0, 0x:ffffff8000b44000, irq_no:6c
[ 5.935301] sunxi-ehci 1c1c000.ehci2-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.945377] sunxi-ehci 1c1c000.ehci2-controller: new USB bus registered, assigned bus number 3
[ 5.955241] sunxi-ehci 1c1c000.ehci2-controller: irq 108, io mem 0xffffffc00047a564
[ 5.978054] sunxi-ehci 1c1c000.ehci2-controller: USB 0.0 started, EHCI 1.00
[ 5.985790] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.993229] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.001141] usb usb3: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.009368] usb usb3: Manufacturer: Linux 3.10.65 ehci_hcd
[ 6.015368] usb usb3: SerialNumber: sunxi-ehci
[ 6.021179] hub 3-0:1.0: USB hub found
[ 6.025308] hub 3-0:1.0: 1 port detected
[ 6.030030] get drv_vbus is fail, 84
[ 6.033939] get ehci3-controller, regulator_io is no nocare
[ 6.040102] [sunxi-ehci3]: probe, pdev->name: 1c1d000.ehci3-controller, sunxi_ehci: 0xffffffc000d18b60, 0x:ffffff8000b4c000, irq_no:6e
[ 6.053399] sunxi-ehci 1c1d000.ehci3-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.063324] sunxi-ehci 1c1d000.ehci3-controller: new USB bus registered, assigned bus number 4
[ 6.073237] sunxi-ehci 1c1d000.ehci3-controller: irq 110, io mem 0xffffffc00047a564
[ 6.096134] sunxi-ehci 1c1d000.ehci3-controller: USB 0.0 started, EHCI 1.00
[ 6.103864] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.111302] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.119214] usb usb4: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.127441] usb usb4: Manufacturer: Linux 3.10.65 ehci_hcd
[ 6.133441] usb usb4: SerialNumber: sunxi-ehci
[ 6.139230] hub 4-0:1.0: USB hub found
[ 6.143354] hub 4-0:1.0: 1 port detected
[ 6.148363] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.155371] get ohci0-controller, regulator_io is no nocare
[ 6.161520] hci: request ohci0-controller gpio:354
[ 6.166771] ohci0-controller get usb clk_usbohci12m clk failed.
[ 6.173246] ohci0-controller get usb clk_hoscx2 clk failed.
[ 6.179349] ohci0-controller get usb clk_hosc failed.
[ 6.184881] ohci0-controller get usb clk_losc clk failed.
[ 6.190786] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000d179e0
[ 6.201035] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 6.210582] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 5
[ 6.220080] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0x76b076c07630720
[ 6.287294] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.294735] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.302638] usb usb5: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 6.310453] usb usb5: Manufacturer: Linux 3.10.65 ohci_hcd
[ 6.316461] usb usb5: SerialNumber: sunxi-ohci
[ 6.322204] hub 5-0:1.0: USB hub found
[ 6.326342] hub 5-0:1.0: 1 port detected
[ 6.331019] get drv_vbus is fail, 84
[ 6.334939] get ohci1-controller, regulator_io is no nocare
[ 6.341085] ohci1-controller get usb clk_usbohci12m clk failed.
[ 6.347570] ohci1-controller get usb clk_hoscx2 clk failed.
[ 6.353673] ohci1-controller get usb clk_hosc failed.
[ 6.359196] ohci1-controller get usb clk_losc clk failed.
[ 6.365109] [sunxi-ohci1]: probe, pdev->name: 1c1b000.ohci1-controller, sunxi_ohci: 0xffffffc000d17c60
[ 6.375356] sunxi-ohci 1c1b000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 6.384902] sunxi-ohci 1c1b000.ohci1-controller: new USB bus registered, assigned bus number 6
[ 6.394396] sunxi-ohci 1c1b000.ohci1-controller: irq 107, io mem 0x76b076c07630720
[ 6.464255] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.471694] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.479597] usb usb6: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 6.487412] usb usb6: Manufacturer: Linux 3.10.65 ohci_hcd
[ 6.493420] usb usb6: SerialNumber: sunxi-ohci
[ 6.499159] hub 6-0:1.0: USB hub found
[ 6.503291] hub 6-0:1.0: 1 port detected
[ 6.507964] get drv_vbus is fail, 84
[ 6.511884] get ohci2-controller, regulator_io is no nocare
[ 6.518029] ohci2-controller get usb clk_usbohci12m clk failed.
[ 6.524514] ohci2-controller get usb clk_hoscx2 clk failed.
[ 6.530617] ohci2-controller get usb clk_hosc failed.
[ 6.536140] ohci2-controller get usb clk_losc clk failed.
[ 6.542057] [sunxi-ohci2]: probe, pdev->name: 1c1c000.ohci2-controller, sunxi_ohci: 0xffffffc000d17ee0
[ 6.552304] sunxi-ohci 1c1c000.ohci2-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 6.561849] sunxi-ohci 1c1c000.ohci2-controller: new USB bus registered, assigned bus number 7
[ 6.571349] sunxi-ohci 1c1c000.ohci2-controller: irq 109, io mem 0x76b076c07630720
[ 6.641370] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.648809] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.656712] usb usb7: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 6.664527] usb usb7: Manufacturer: Linux 3.10.65 ohci_hcd
[ 6.670535] usb usb7: SerialNumber: sunxi-ohci
[ 6.676266] hub 7-0:1.0: USB hub found
[ 6.680404] hub 7-0:1.0: 1 port detected
[ 6.685077] get drv_vbus is fail, 84
[ 6.688997] get ohci3-controller, regulator_io is no nocare
[ 6.695142] ohci3-controller get usb clk_usbohci12m clk failed.
[ 6.701627] ohci3-controller get usb clk_hoscx2 clk failed.
[ 6.707730] ohci3-controller get usb clk_hosc failed.
[ 6.713253] ohci3-controller get usb clk_losc clk failed.
[ 6.719165] [sunxi-ohci3]: probe, pdev->name: 1c1d000.ohci3-controller, sunxi_ohci: 0xffffffc000d18160
[ 6.729413] sunxi-ohci 1c1d000.ohci3-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 6.738956] sunxi-ohci 1c1d000.ohci3-controller: new USB bus registered, assigned bus number 8
[ 6.748452] sunxi-ohci 1c1d000.ohci3-controller: irq 111, io mem 0x76b076c07630720
[ 6.818495] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.825936] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.833838] usb usb8: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 6.841652] usb usb8: Manufacturer: Linux 3.10.65 ohci_hcd
[ 6.847661] usb usb8: SerialNumber: sunxi-ohci
[ 6.853377] hub 8-0:1.0: USB hub found
[ 6.857510] hub 8-0:1.0: 1 port detected
[ 6.862871] usbcore: registered new interface driver usb-storage
[ 6.869666] usbcore: registered new interface driver ums-alauda
[ 6.876355] usbcore: registered new interface driver ums-cypress
[ 6.883128] usbcore: registered new interface driver ums-datafab
[ 6.889915] usbcore: registered new interface driver ums_eneub6250
[ 6.896886] usbcore: registered new interface driver ums-freecom
[ 6.903673] usbcore: registered new interface driver ums-isd200
[ 6.910344] usbcore: registered new interface driver ums-jumpshot
[ 6.917213] usbcore: registered new interface driver ums-karma
[ 6.923802] usbcore: registered new interface driver ums-onetouch
[ 6.930681] usbcore: registered new interface driver ums-realtek
[ 6.937462] usbcore: registered new interface driver ums-sddr09
[ 6.944150] usbcore: registered new interface driver ums-sddr55
[ 6.950821] usbcore: registered new interface driver ums-usbat
[ 6.958043] usbcore: registered new interface driver usbserial
[ 6.964645] usbcore: registered new interface driver option
[ 6.970925] usbserial: USB Serial support registered for GSM modem (1-port)
[ 6.980305] mousedev: PS/2 mouse device common for all mice
[ 6.987258] usbcore: registered new interface driver xpad
[ 6.993386] usbcore: registered new interface driver usb_acecad
[ 7.000065] usbcore: registered new interface driver aiptek
[ 7.006383] usbcore: registered new interface driver gtco
[ 7.012501] usbcore: registered new interface driver hanwang
[ 7.018903] usbcore: registered new interface driver kbtab
[ 7.025155] usbcore: registered new interface driver wacom
[ 7.032692] Set vaild hardware RTC date 2016-01-01
[ 7.038558] sunxi-rtc 1f00000.rtc: rtc core: registered sunxi-rtc as rtc0
[ 7.046041] sunxi-rtc 1f00000.rtc: RTC enabled
[ 7.051611] IR NEC protocol handler initialized
[ 7.056565] IR RC5(x) protocol handler initialized
[ 7.061812] IR RC6 protocol handler initialized
[ 7.066764] IR JVC protocol handler initialized
[ 7.071730] IR Sony protocol handler initialized
[ 7.076777] IR RC5 (streamzap) protocol handler initialized
[ 7.082877] IR SANYO protocol handler initialized
[ 7.088019] IR MCE Keyboard/mouse protocol handler initialized
[ 7.094403] sunxi cedar version 0.1
[ 7.098417] [cedar]: install start!!!
[ 7.102530] cedar_ve: cedar-ve the get irq is 90
[ 7.108221] [cedar]: install end!!!
[ 7.124535] sunxi gpu cooling probe start !
[ 7.129131] CPU gpu cooling register Success
[ 7.134241] device-mapper: uevent: version 1.0.3
[ 7.139783] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 7.149218] Bluetooth: HCI UART driver ver 2.2
[ 7.154078] Bluetooth: HCI H4 protocol initialized
[ 7.159327] Bluetooth: HCI Realtek H5 protocol initialized
[ 7.165325] rtk_btcoex: rtk_uart_coex_init, version: 1.1
[ 7.171148] rtk_btcoex: create workqueue
[ 7.176374] cpuidle: using governor ladder
[ 7.180873] cpuidle: using governor menu
[ 7.187080] sunxi-mmc 1c0f000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.54 2016-05-11 21:04) Compiled in Nov 18 2016 at 16:16:31
[ 7.200106] sunxi-mmc 1c0f000.sdmmc: regulator prop vmmc,str vcc-sdcv
[ 7.207154] sunxi-mmc 1c0f000.sdmmc: regulator prop vqmmc,str vcc-sdcvq33
[ 7.214597] sunxi-mmc 1c0f000.sdmmc: regulator prop vdmmc,str vcc-sdcvd
[ 7.221857] sunxi-mmc 1c0f000.sdmmc: No vmmc regulator found
[ 7.228056] sunxi-mmc 1c0f000.sdmmc: No vqmmc regulator found
[ 7.234340] sunxi-mmc 1c0f000.sdmmc: No vdmmc regulator found
[ 7.241157] sunxi-mmc 1c0f000.sdmmc: Got CD GPIO #166.
[ 7.247186] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 7.276937] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 7.306809] sunxi-mmc 1c0f000.sdmmc: base:0xffffff8000b6c000 irq:92
[ 7.313673] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !!
[ 7.321166] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !!
[ 7.327856] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 7.336399] hidraw: raw HID events driver (C) Jiri Kosina
[ 7.347669] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 7.350236] usbcore: registered new interface driver usbhid
[ 7.350238] usbhid: USB HID core driver
[ 7.351206] zram: Created 1 device(s) ...
[ 7.374740] ashmem: initialized
[ 7.376032] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 7.376848] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 7.377662] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 7.378477] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 7.379115] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 7.379164] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 7.381540] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 7.439054] logger: created 256K log 'log_main'
[ 7.443084] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 7.446485] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 7.446529] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 7.447160] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 4 timing SD-HS(SDR25) dt B
[ 7.447460] mmc0: new high speed SDHC card at address aaaa
[ 7.493829] logger: created 256K log 'log_events'
[ 7.499016] mmcblk0: mmc0:aaaa SL08G 7.40 GiB
[ 7.499392] logger: created 256K log 'log_radio'
[ 7.499739] logger: created 256K log 'log_system'
[ 7.502963] AUDIO :get regulator name failed .
[ 7.520403] sunxi-codec-machine sound.6: sun50iw2codec <-> 1c22c00.cpudai0-controller mapping ok
[ 7.520654] mmcblk0: p1 p2
[ 7.537111] sndhdmi sound.7: sndhdmi <-> 1c22800.daudio mapping ok
[ 7.546587] u32 classifier
[ 7.549554] Actions configured
[ 7.553290] Netfilter messages via NETLINK v0.30.
[ 7.558548] nf_conntrack version 0.5.0 (7833 buckets, 31332 max)
[ 7.565630] ctnetlink v0.93: registering with nfnetlink.
[ 7.573735] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 7.581355] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 7.589109] xt_time: kernel timezone is -0000
[ 7.594021] ipip: IPv4 over IPv4 tunneling driver
[ 7.600284] gre: GRE over IPv4 demultiplexor driver
[ 7.605635] ip_gre: GRE over IPv4 tunneling driver
[ 7.613453] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.619746] arp_tables: (C) 2002 David S. Miller
[ 7.624940] TCP: bic registered
[ 7.628373] TCP: cubic registered
[ 7.632005] TCP: westwood registered
[ 7.635912] TCP: htcp registered
[ 7.639437] Initializing XFRM netlink socket
[ 7.644481] NET: Registered protocol family 10
[ 7.652185] mip6: Mobile IPv6
[ 7.655514] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.661928] sit: IPv6 over IPv4 tunneling driver
[ 7.668435] NET: Registered protocol family 17
[ 7.673381] NET: Registered protocol family 15
[ 7.678794] Bluetooth: RFCOMM TTY layer initialized
[ 7.684187] Bluetooth: RFCOMM socket layer initialized
[ 7.689805] Bluetooth: RFCOMM ver 1.11
[ 7.693913] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 7.699720] Bluetooth: BNEP filters: protocol multicast
[ 7.705467] Bluetooth: BNEP socket layer initialized
[ 7.710908] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 7.717406] Bluetooth: HIDP socket layer initialized
[ 7.723467] Registering SWP/SWPB emulation handler
[ 7.730542] [DISP] boot_disp:0x0
[ 7.735508] [HDMI] cec support = 1
[ 7.849213] there is no tve dac(0) offset value.
[ 7.854275] [DISP] boot_disp:0x0
[ 7.857955] [DISP] disp_init_tv,line:641:screen 0 don't support TV!
[ 8.447895] [DISP] disp_device_attached_and_enable,line:165:attched ok, mgr0<-->device0, type=4, mode=4
[ 8.459017] usb_serial_number:20080411
[ 8.463912] file system registered
[ 8.471804] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 8.479351] android_usb gadget: Number of LUNs=3
[ 8.484439] lun0: LUN: removable file: (no medium)
[ 8.489784] lun1: LUN: removable file: (no medium)
[ 8.495117] lun2: LUN: removable file: (no medium)
[ 8.501356] android_usb gadget: android_usb ready
[ 8.506711] sunxi-rtc 1f00000.rtc: setting system clock to 2016-01-01 00:00:08 UTC (1451606408)
[ 8.525285] ALSA device list:
[ 8.528571] #0: audiocodec
[ 8.531717] #1: sndhdmi
[ 8.535202] Freeing unused kernel memory: 548K (ffffffc000ad0000 - ffffffc000b59000)
Kernel params: console=tty0 console=ttyS0,115200n8 no_console_suspend earlycon=uart,mmio32,0x01c28000 mac_addr=96:62:08:fb:22:8a root=/dev/mmcblk0p2 ro rootwait
Waiting for root system /dev/mmcblk0p2, countdown : 5
Rootfs: /dev/mmcblk0p2
[ 8.637709] EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
[ 8.648589] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[ 8.671550] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 8.985476] systemd[1]: System time before build time, advancing clock.
[ 9.009406] systemd[1]: Failed to insert module 'autofs4': No such file or directory
[ 9.049523] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 9.070261] systemd[1]: Detected architecture arm64.
Welcome to Ubuntu 16.04.1 LTS!
[ 9.108330] systemd[1]: Set hostname to .
[ 9.399755] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ 9.432457] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 9.461508] systemd[1]: Reached target Encrypted Volumes.
[ OK ] Reached target Encrypted Volumes.
[ 9.491546] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 9.520550] systemd[1]: Reached target Remote File Systems (Pre).
[ OK ] Reached target Remote File Systems (Pre).
[ 9.550695] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ 9.579721] systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ 9.609087] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 9.629289] systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
[ 9.648817] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 9.678270] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ 9.707962] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 9.729692] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
[ 9.749803] systemd[1]: Starting Create list of required static device nodes for the current kernel...
Starting Create list of required st... nodes for the current kernel...
[ 9.788826] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 9.818413] systemd[1]: Starting Set console keymap...
Starting Set console keymap...
[ 9.826606] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 9.852713] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 9.877975] systemd[1]: Starting Nameserver information manager...
Starting Nameserver information manager...
[ 9.904432] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 9.934341] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 9.959731] [VFE]cci probe end cci_sel = 0!
[ 9.964835] [VFE]cci_init end
[ 9.965049] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 10.013037] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 10.034928] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 10.052428] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 10.081692] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 10.107861] systemd[1]: Mounted Debug File System.
[ OK ] Mounted Debug File System.
[ 10.126562] [VFE]Welcome to Video Front End driver
[ 10.132267] [VFE]csi0 probe end!
[ 10.133920] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ OK [ 10.146198] [VFE]csi_init end
] Started Create list of require[ 10.151836] [ISP] isp platform_id = 3!
d sta...ce nodes for the current[ 10.157634] [VFE]isp0 probe end!
kernel.
[ 10.164348] [VFE]sunxi_isp_platform_register end
[ 10.170328] [VFE]mipi_init end
[ 10.173687] [VFE]flash_init end
[ 10.179287] [VFE]pdev->id = 0
[ 10.182636] [VFE]dev->cci_sel = 0
[ 10.184491] systemd[1]: Started Remount Root and Kernel File Systems.
[ 10.193394] [VFE]dev->csi_sel = 0
[ 10.197026] [VFE]dev->mipi_sel = 0
[[ 10.200761] [VFE]dev->isp_sel = 0
OK [ 10.204491] [VFE_WARN]fetch csi0_dev0_twi_id from device_tree failed
] Started Remount Root and Kerne[ 10.212906] [VFE_WARN]fetch csi0_dev0_iovdd from device_tree failed
l File Systems.
[ 10.222499] [VFE_WARN]fetch csi0_dev0_avdd from device_tree failed
[ 10.230705] [VFE_WARN]fetch csi0_dev0_dvdd from device_tree failed
[ 10.237472] [VFE_WARN]fetch csi0_dev0_afvdd from device_tree failed
[ 10.238919] systemd[1]: Started Set console keymap.
[ 10.249736] [VFE_WARN]fetch csi0_dev0_flash_en from device_tree failed
[ 10.256886] [VFE_WARN]fetch csi0_dev0_flash_mode from device_tree failed
[ 10.264238] [VFE_WARN]fetch csi0_dev0_flvdd from device_tree failed
[ OK [ 10.271132] [VFE_WARN]fetch csi0_dev0_flvdd_vol from device_tree failed
] [ 10.279893] [VFE_WARN]fetch csi0_dev0_af_pwdn from device_tree failed
Started Set console keymap.
[ 10.287747] [VFE]vfe_init end
[ 10.292841] [VFE]probe_work_handle start!
[ 10.297478] [VFE]vfe_runtime_resume
[ 10.306596] systemd[1]: Started Load Kernel Modules.
[ OK [ 10.313305] [VFE]..........................vfe clk open!.......................
] Started Load Kernel Modules.
[ 10.322194] [VFE]v4l2 subdev register input_num = 0
[ 10.330220] [VFE]vfe sensor detect start! input_num = 0
[ 10.336017] [VFE]Find sensor name is "gc2035", i2c address is 78, type is "YUV" !
[ 10.344226] [VFE]Sub device register "gc2035" i2c_addr = 0x78 start!
[ 10.351232] [VFE]v4l2_device_register_subdev return 0
[ 10.356759] [VFE]registered sensor subdev is OK!
[ 10.361835] [VFE]Check sensor!
[ 10.365110] systemd[1]: Started Nameserver information manager.
[ OK ] Started Nameserver information manager.
[ 10.383749] [VFE]mclk on
[ 10.390753] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ 10.441115] [VFE CCI_0 ERR] Status error at addr_8bit = 78, wr_flag = 1, val = 3efb9cf0
[ 10.450479] [VFE CCI_0 ERR] Status error at addr_8bit = 78, wr_flag = 1, val = 3efb00f0
[ 10.459593] [VFE CCI_0 ERR] Status error at addr_8bit = 78, wr_flag = 1, val = 3efb00f0
[ 10.468750] gc2035 sensor read retry=2
[ 10.472868] [CSI_ERR][GC2035]sensor_read err at sensor_detect!
[ 10.479696] [CSI_ERR][GC2035]chip found is not an target chip.
Mounting FUSE Control File System...
Starting Apply Kernel Variables...
[ 10.526182] [VFE]mclk off
Mounting Configuration File System...
[ 10.552899] [VFE_ERR]vfe sensor register check error at input_num = 0
Starting udev Coldplug all Devices...
Starting Load/Save Random Seed...
Starting Flush Journal to Persistent Storage...
Starting Create Static Device Nodes in /dev...
[ OK ] Mounted FUSE Control File System.
[ OK ] Mounted Configuration File System.
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Found device /dev/ttyS0.
[ OK ] Reached target Sound Card.
[ 11.574583] node ir_addr_code16 get failed!
[ 11.581659] sunxi_ir_startup: cir get supply err
[ OK ] Found device /dev/mmcblk0p1.
Starting File System Check on /dev/mmcblk0p1...
[ OK ] Started File System Check on /dev/mmcblk0p1.
Mounting /boot...
[ OK ] Started File System Check Daemon to report status.
[ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[ OK ] Mounted /boot.
[ OK ] Reached target Local File Systems.
Starting Raise network interfaces...
Starting Set console font and keymap...
Starting Create Volatile Files and Directories...
[ OK ] Started ifup for eth0.
[ OK ] Started Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Network Time Synchronization.
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Started Trigger resolvconf update for networkd DNS.
[ OK ] Reached target Paths.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Basic System.
Starting Permit User Sessions...
[ OK ] Started OrangePi add audio configure.
Starting Save/Restore Sound Card State...
[ OK ] Started CPU corekeeper.
Starting Login Service...
Starting Generate SSH keys if not there...
[ OK ] Started D-Bus System Message Bus.
Starting System Logging Service...
Starting Fix eth0 mac address to uEnv.txt...
[ OK ] Started Regular background program processing daemon.
Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Daily apt activities.
[ OK ] Reached target Timers.
[ OK ] Started System Logging Service.
[ OK ] Started Set console font and keymap.
[ OK ] Started Permit User Sessions.
[ OK ] Started Generate SSH keys if not there.
[ OK ] Started Fix eth0 mac address to uEnv.txt.
[ OK ] Started Save/Restore Sound Card State.
[ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
[ OK ] Started Login Service.
[ OK ] Started Serial Getty on ttyS0.
Starting Set console scheme...
[ OK ] Created slice system-getty.slice.
[ OK ] Started Set console scheme.
Ubuntu 16.04.1 LTS Orangepi ttyS0
Orangepi login:
Have any comments? Questions?
Drop me a line!
Tom's electronics pages / tom@mmto.org