July 26, 2018
Nanopi Fire3 first boot messages
The following is what I get when I put the following image onto
an SD card and apply power:
- s5p6818-friendly-core-xenial-4.4-arm64-20180615.img
BL1 by Nexell V1.0.0-g44b48cd [Built on 2017-08-02 15:58:54]
Memory Initialize (0) Done.
Loading from sdmmc...
Image Loading Done!
Launch to 0x7FD00800
U-Boot 2016.01-00025-gb5566ab172 (May 09 2018 - 13:52:47 +0800)
Model: FriendlyElec boards based on Nexell s5p6818
Board: NanoPi Fire 3
DRAM: 987 MiB
Panel: N/A (-1)
MMC: NEXELL DWMMC: 0, NEXELL DWMMC: 1
HDMI: display.0, preset 0 (1280 * 720)
HDMI: phy ready...
LCD: [HDMI] dp.0.1 1280x720 32bpp FB:0x46000000
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
14562000 bytes read in 697 ms (19.9 MiB/s)
4512648 bytes read in 224 ms (19.2 MiB/s)
47839 bytes read in 15 ms (3 MiB/s)
## Flattened Device Tree blob at 49000000
Booting using the fdt blob at 0x49000000
reserving fdt memory region: addr=7de00000 size=100000
Using Device Tree in place at 0000000049000000, end 000000004900eade
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.49-s5p6818 (root@jensen) (gcc version 6.4.0 (ctng-1.23.0-150g-FA) ) #1 SMP PREEMPT Wed May 9 14:01:02 CST 2018
[ 0.000000] Boot CPU: AArch64 Processor [410fd033]
[ 0.000000] Machine model: FriendlyElec NanoPi Fire3
[ 0.000000] Display: HDMI selected
[ 0.000000] cma: Reserved 192 MiB at 0x0000000071000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc03d9f7000 s46056 r8192 d31768 u86016
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 248724
[ 0.000000] Kernel command line: console=ttySAC0,115200n8 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait init=/sbin/init loglevel=7 printk.time=1 consoleblank=0 lcd=HDMI720P60 bootdev=2
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Memory: 767104K/1010688K available (9464K kernel code, 1036K rwdata, 3152K rodata, 548K init, 1069K bss, 46976K reserved, 196608K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB)
[ 0.000000] .init : 0xffffff8008cd7000 - 0xffffff8008d60000 ( 548 KB)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff80089bf000 ( 9468 KB)
[ 0.000000] .rodata : 0xffffff80089bf000 - 0xffffff8008cd7000 ( 3168 KB)
[ 0.000000] .data : 0xffffff8008d60000 - 0xffffff8008e632d0 ( 1037 KB)
[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
[ 0.000000] 0xffffffbdc0000000 - 0xffffffbdc0f6c000 ( 15 MB actual)
[ 0.000000] fixed : 0xffffffbffe7fd000 - 0xffffffbffec00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc03db00000 ( 987 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] PLL : [0] = 800000000, [1] = 800000000, [2] = 614394000, [3] = 800000000
[ 0.000000] (0) PLL1: CPU FCLK = 800000000, HCLK = 200000000 (G0)
[ 0.000000] (7) PLL1: CPU FCLK = 800000000, HCLK = 200000000 (G1)
[ 0.000000] (2) PLL3: MEM FCLK = 800000000, DCLK = 800000000, BCLK = 400000000,
[ 0.000000] PCLK = 200000000
[ 0.000000] (1) PLL0: BUS BCLK = 400000000, PCLK = 200000000
[ 0.000000] (8) PLL3: CCI4 BCLK = 400000000, PCLK = 200000000
[ 0.000000] (3) PLL0: G3D BCLK = 400000000
[ 0.000000] (4) PLL0: VPU BCLK = 400000000, PCLK = 200000000
[ 0.000000] (5) PLL0: DISP BCLK = 400000000, PCLK = 200000000
[ 0.000000] CPU REF HZ: 24000000 hz (0xc0010000:0xffffff8008004000)
[ 0.000000] clocksource: source timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 191126044627 ns
[ 0.000000] sched_clock: 64 bits at 250 Hz, resolution 4000000ns, wraps every 9007199254000000ns
[ 0.000000] Console: colour dummy device 80x25
[ 0.040000] Calibrating delay loop... 19.84 BogoMIPS (lpj=39680)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Security Framework initialized
[ 0.044000] Yama: becoming mindful.
[ 0.044000] SELinux: Initializing.
[ 0.044000] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.044000] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.044000] Initializing cgroup subsys memory
[ 0.044000] Initializing cgroup subsys devices
[ 0.044000] Initializing cgroup subsys freezer
[ 0.044000] Initializing cgroup subsys hugetlb
[ 0.044000] sched-energy: CPU device node has no sched-energy-costs
[ 0.044000] Invalid sched_group_energy for CPU0
[ 0.044000] CPU0: update cpu_capacity 1024
[ 0.044000] ASID allocator initialised with 256 entries
[ 0.080000] Detected VIPT I-cache on CPU1
[ 0.080000] Invalid sched_group_energy for CPU1
[ 0.080000] CPU1: update cpu_capacity 1024
[ 0.080000] CPU1: Booted secondary processor [410fd033]
[ 0.092000] Detected VIPT I-cache on CPU2
[ 0.092000] Invalid sched_group_energy for CPU2
[ 0.092000] CPU2: update cpu_capacity 1024
[ 0.092000] CPU2: Booted secondary processor [410fd033]
[ 0.104000] Detected VIPT I-cache on CPU3
[ 0.104000] Invalid sched_group_energy for CPU3
[ 0.104000] CPU3: update cpu_capacity 1024
[ 0.104000] CPU3: Booted secondary processor [410fd033]
[ 0.116000] Detected VIPT I-cache on CPU4
[ 0.116000] Invalid sched_group_energy for CPU4
[ 0.116000] CPU4: update cpu_capacity 1024
[ 0.116000] CPU4: Booted secondary processor [410fd033]
[ 0.128000] Detected VIPT I-cache on CPU5
[ 0.128000] Invalid sched_group_energy for CPU5
[ 0.128000] CPU5: update cpu_capacity 1024
[ 0.128000] CPU5: Booted secondary processor [410fd033]
[ 0.140000] Detected VIPT I-cache on CPU6
[ 0.140000] Invalid sched_group_energy for CPU6
[ 0.140000] CPU6: update cpu_capacity 1024
[ 0.140000] CPU6: Booted secondary processor [410fd033]
[ 0.152000] Detected VIPT I-cache on CPU7
[ 0.152000] Invalid sched_group_energy for CPU7
[ 0.152000] CPU7: update cpu_capacity 1024
[ 0.152000] CPU7: Booted secondary processor [410fd033]
[ 0.152000] Brought up 8 CPUs
[ 0.152000] SMP: Total of 8 processors activated.
[ 0.152000] CPU features: GIC system register CPU interface present but disabled by higher exception level
[ 0.152000] CPU: All CPU(s) started at EL2
[ 0.152000] alternatives: patching kernel code
[ 0.152000] Invalid sched_group_energy for CPU7
[ 0.152000] CPU7: update max cpu_capacity 1024
[ 0.152000] Invalid sched_group_energy for Cluster7
[ 0.152000] Invalid sched_group_energy for CPU6
[ 0.152000] Invalid sched_group_energy for Cluster6
[ 0.152000] Invalid sched_group_energy for CPU5
[ 0.152000] Invalid sched_group_energy for Cluster5
[ 0.152000] Invalid sched_group_energy for CPU4
[ 0.152000] Invalid sched_group_energy for Cluster4
[ 0.152000] Invalid sched_group_energy for CPU3
[ 0.152000] Invalid sched_group_energy for Cluster3
[ 0.152000] Invalid sched_group_energy for CPU2
[ 0.152000] Invalid sched_group_energy for Cluster2
[ 0.152000] Invalid sched_group_energy for CPU1
[ 0.152000] Invalid sched_group_energy for Cluster1
[ 0.152000] Invalid sched_group_energy for CPU0
[ 0.152000] Invalid sched_group_energy for Cluster0
[ 0.152000] devtmpfs: initialized
[ 0.156000] CPU1: update max cpu_capacity 1024
[ 0.184000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.192000] pinctrl core: initialized pinctrl subsystem
[ 0.192000] ECID: 6d30f012:0e3001b6:00000000:04e81234
[ 0.192000] LOT ID : NCNHD
[ 0.192000] NET: Registered protocol family 16
[ 0.204000] cpuidle: using governor ladder
[ 0.228000] cpuidle: using governor menu
[ 0.228000] vdso: 2 pages (1 code @ ffffff80089c5000, 1 data @ ffffff8008d64000)
[ 0.228000] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.232000] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.240000] nexell-reset c0012000.reset: nexell reset: nr_resets [96], base [ffffff800806e000]
[ 0.280000] pl08xdmac c0000000.pl08xdma: initialized 8 virtual memcpy channels
[ 0.280000] pl08xdmac c0000000.pl08xdma: initialized 16 virtual slave channels
[ 0.284000] pl08xdmac c0000000.pl08xdma: DMA: PL080 rev0 at 0xc0000000 irq 16
[ 0.284000] pl08xdmac c0001000.pl08xdma: initialized 8 virtual memcpy channels
[ 0.284000] pl08xdmac c0001000.pl08xdma: initialized 15 virtual slave channels
[ 0.288000] pl08xdmac c0001000.pl08xdma: DMA: PL080 rev0 at 0xc0001000 irq 17
[ 0.288000] c00a1000.serial: ttySAC0 at MMIO 0xc00a1000 (irq = 18, base_baud = 0) is a S3C6400/10
[ 1.048000] console [ttySAC0] enabled
[ 1.052000] c00a0000.serial: ttySAC1 at MMIO 0xc00a0000 (irq = 19, base_baud = 0) is a S3C6400/10
[ 1.060000] c00a2000.serial: ttySAC2 at MMIO 0xc00a2000 (irq = 20, base_baud = 0) is a S3C6400/10
[ 1.072000] c00a3000.serial: ttySAC3 at MMIO 0xc00a3000 (irq = 21, base_baud = 0) is a S3C6400/10
[ 1.080000] c006d000.serial: ttySAC4 at MMIO 0xc006d000 (irq = 22, base_baud = 0) is a S3C6400/10
[ 1.088000] SCSI subsystem initialized
[ 1.092000] usbcore: registered new interface driver usbfs
[ 1.096000] usbcore: registered new interface driver hub
[ 1.100000] usbcore: registered new device driver usb
[ 1.140000] axp_mfd 3-0034: failed reading at 0x03
[ 1.140000] [AXP22-MFD] try to read chip id failed!
[ 1.144000] axp_mfd 3-0034: axp_mfd_probe() Error: init_chip()
[ 1.152000] i2c-gpio c0000000.soc:i2c@3: using pins 159 (SDA) and 158 (SCL)
[ 1.160000] s3c-i2c c00a4000.i2c: slave address 0x66
[ 1.164000] s3c-i2c c00a4000.i2c: bus frequency set to 390 KHz
[ 1.168000] s3c-i2c c00a4000.i2c: i2c-0: S3C I2C adapter
[ 1.176000] s3c-i2c c00a5000.i2c: slave address 0x66
[ 1.180000] s3c-i2c c00a5000.i2c: bus frequency set to 97 KHz
[ 1.184000] s3c-i2c c00a5000.i2c: i2c-1: S3C I2C adapter
[ 1.192000] s3c-i2c c00a6000.i2c: slave address 0x66
[ 1.196000] s3c-i2c c00a6000.i2c: bus frequency set to 195 KHz
[ 1.200000] s3c-i2c c00a6000.i2c: i2c-2: S3C I2C adapter
[ 1.204000] media: Linux media interface: v0.10
[ 1.212000] Linux video capture interface: v2.00
[ 1.216000] pps_core: LinuxPPS API ver. 1 registered
[ 1.220000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 1.228000] PTP clock support registered
[ 1.232000] Advanced Linux Sound Architecture Driver Initialized.
[ 1.240000] Bluetooth: Core ver 2.21
[ 1.244000] NET: Registered protocol family 31
[ 1.248000] Bluetooth: HCI device and connection manager initialized
[ 1.252000] Bluetooth: HCI socket layer initialized
[ 1.256000] Bluetooth: L2CAP socket layer initialized
[ 1.264000] Bluetooth: SCO socket layer initialized
[ 1.268000] NetLabel: Initializing
[ 1.272000] NetLabel: domain hash size = 128
[ 1.276000] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.280000] NetLabel: unlabeled traffic allowed by default
[ 1.288000] clocksource: Switched to clocksource source timer
[ 1.292000] Clockevents: could not switch to one-shot mode:
[ 1.292000] Clockevents: could not switch to one-shot mode:
[ 1.292000] Clockevents: could not switch to one-shot mode:
[ 1.292000] dummy_timer is not functional.
[ 1.292000] Clockevents: could not switch to one-shot mode:
[ 1.292000] Could not switch to high resolution mode on CPU 2
[ 1.292000] dummy_timer is not functional.
[ 1.292000] dummy_timer is not functional.
[ 1.292000] dummy_timer is not functional.
[ 1.292000] Could not switch to high resolution mode on CPU 0
[ 1.292000] Could not switch to high resolution mode on CPU 1
[ 1.292000] Clockevents: could not switch to one-shot mode:
[ 1.292000] Could not switch to high resolution mode on CPU 3
[ 1.292000] Clockevents: could not switch to one-shot mode:
[ 1.292000] Clockevents: could not switch to one-shot mode:
[ 1.292000] dummy_timer is not functional.
[ 1.292000] dummy_timer is not functional.
[ 1.292000] dummy_timer is not functional.
[ 1.292000] Could not switch to high resolution mode on CPU 5
[ 1.292000] Could not switch to high resolution mode on CPU 7
[ 1.292000] Could not switch to high resolution mode on CPU 4
[ 1.292000] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[ 1.292000] Could not switch to high resolution mode on CPU 6
[ 1.528000] FS-Cache: Loaded
[ 1.528000] CacheFiles: Loaded
[ 1.528000] io scheduler noop registered
[ 1.532000] io scheduler deadline registered
[ 1.536000] io scheduler cfq registered (default)
[ 1.556000] dwmmc_nexell c0062000.dw_mmc: fifo-depth property not found, using value of FIFOTH register as default
[ 1.564000] dwmmc_nexell c0062000.dw_mmc: IDMAC supports 32-bit address mode.
[ 1.572000] dwmmc_nexell c0062000.dw_mmc: Using internal DMA controller.
[ 1.576000] dwmmc_nexell c0062000.dw_mmc: Version ID is 250a
[ 1.584000] dwmmc_nexell c0062000.dw_mmc: DW MMC controller at irq 26,32 bit host data width,16 deep fifo
[ 1.592000] dwmmc_nexell c0062000.dw_mmc: No vmmc regulator found
[ 1.596000] dwmmc_nexell c0062000.dw_mmc: No vqmmc regulator found
[ 1.604000] dwmmc_nexell c0062000.dw_mmc: Got CD GPIO
[ 1.640000] mmc0: run _mmc_detect_change()
[ 1.640000] dwmmc_nexell c0062000.dw_mmc: 1 slots initialized
[ 1.644000] NET: Registered protocol family 2
[ 1.648000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.652000] TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.660000] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.668000] UDP hash table entries: 512 (order: 3, 49152 bytes)
[ 1.672000] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes)
[ 1.680000] NET: Registered protocol family 1
[ 1.684000] RPC: Registered named UNIX socket transport module.
[ 1.688000] RPC: Registered udp transport module.
[ 1.692000] RPC: Registered tcp transport module.
[ 1.700000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.704000] Trying to unpack rootfs image as initramfs...
[ 1.712000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 1.720000] mmc0: new high speed SDHC card at address aaaa
[ 1.728000] mmcblk0: mmc0:aaaa SL08G 7.40 GiB
[ 1.732000] mmcblk0: p1 p2
[ 1.992000] Freeing initrd memory: 4404K (ffffffc008000000 - ffffffc00844d000)
[ 1.996000] Initcalls thread level:6
[ 2.000000] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 2.008000] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 2.012000] audit: initializing netlink subsys (disabled)
[ 2.016000] audit: type=2000 audit(2.016:1): initialized
[ 2.020000] Initialise system trusted keyring
[ 2.024000] HugeTLB registered 2 MB page size, pre-allocated 0 pages
Loading, please wait...
mount: mounting devpts on /dev/pts failed: No such device
[ 2.052000] FS-Cache: Netfs 'nfs' registered for caching
[ 2.052000] NFS: Registering the id_resolver key type
[ 2.056000] Key type id_resolver registered
[ 2.060000] Key type id_legacy registered
[ 2.068000] fuse init (API version 7.23)
[ 2.068000] random: systemd-udevd: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
[ 2.068000] random: systemd-udevd: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
[ 2.068000] random: systemd-udevd: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
[ 2.068000] random: systemd-udevd: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
[ 2.068000] random: systemd-udevd: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
[ 2.068000] random: systemd-udevd: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
[ 2.068000] random: systemd-udevd: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
[ 2.068000] random: udevadm: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
[ 2.068000] random: udevadm: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
[ 2.068000] random: udevadm: uninitialized urandom read (16 bytes read, 16 bits of entropy available)
starting version 229
[ 2.120000] NET: Registered protocol family 38
[ 2.120000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 2.132000] spu1705 3-002d: found chip 0x4d, rev 1711
[ 2.140000] [drm] Initialized drm 1.1.0 20060810
[ 2.140000] [drm] Load LVDS panel
[ 2.144000] [drm] Load HDMI panel
[ 2.144000] [drm] irq 37 install for hdp
[ 2.152000] [drm] num of crtcs 2, FB align 1
[ 2.152000] [drm] crtc[0]: pipe.0
[ 2.156000] [drm] crtc[1]: pipe.1
[ 2.160000] [drm] Bind LVDS panel
[ 2.164000] nexell,display_drm c0102800.display_drm: bound c0101000.display_drm_lvds (ops 0xffffff8008a3a7f0)
[ 2.172000] [drm] Bind HDMI panel
[ 2.176000] [drm] HDMI force connected at boot
[ 2.180000] nexell,display_drm c0102800.display_drm: bound c0101000.display_drm_hdmi (ops 0xffffff8008a3ad10)
[ 2.192000] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.196000] [drm] No driver support for vblank timestamp query.
[ 2.204000] [drm] HDMI: connect
[ 2.208000] [drm] FB counts = 3, FB vblank Pass fb crtcs 2 [0xff]
[ 2.212000] [drm] HDMI: connect
[ 2.216000] [drm] framebuffer width(1280), height(720) and bpp(32) buffers(3)
[ 2.240000] [drm] Copy splash image from 0x46000000(0xffffff8009d8e000) to 0xffffff8009301000 size 3686400
[ 2.288000] HDMI: PHY [Ready Done][0x1] ...
[ 2.312000] [drm] request CRTC.35 IRQ 0
[ 2.328000] Console: switching to colour frame buffer device 160x45
[ 2.352000] nexell,display_drm c0102800.display_drm: fb0: frame buffer device
[ 2.372000] [drm] Initialized nexell 3.0.0 20160219 on minor 0
[ 2.376000] Mali: Mali device driver loaded
[ 2.376000] Unable to detect cache hierarchy from DT for CPU 0
[ 2.396000] brd: module loaded
[ 2.408000] loop: module loaded
[ 2.420000] nexell-dwmac c0060000.ethernet: snps,phy-addr property is deprecated
[ 2.420000] stmmac - user ID: 0x37, Synopsys ID: 0x37
[ 2.428000] Ring mode enabled
[ 2.428000] DMA HW capability register supported
[ 2.432000] Enhanced/Alternate descriptors
[ 2.436000] Enabled extended descriptors
[ 2.440000] RX Checksum Offload Engine supported (type 2)
[ 2.448000] TX Checksum insertion supported
[ 2.452000] Wake-Up On Lan supported
[ 2.456000] Enable RX Mitigation via HW Watchdog Timer
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 2.524000] libphy: stmmac: probed
[ 2.524000] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00)
[ 2.528000] eth%d: PHY ID 001cc915 at 7 IRQ POLL (stmmac-0:07) active
[ 2.536000] PPP generic driver version 2.4.2
[ 2.536000] PPP BSD Compression module registered
[ 2.544000] PPP Deflate Compression module registered
[ 2.548000] PPP MPPE Compression module registered
[ 2.552000] NET: Registered protocol family 24
[ 2.556000] c0040000.dwc2otg supply vusb_d not found, using dummy regulator
[ 2.564000] c0040000.dwc2otg supply vusb_a not found, using dummy regulator
Begin: Will now check root file system ... fsck from util-linux 2.27.1
[/sbin/fsck.ext4 (1) -- /dev/mmcblk0p2] fsck.ext4 -a -C0 /dev/mmcblk0p2
rootfs: clean, 90860/232000 files, 650446/934740 blocks
done.
[ 2.640000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
Begin: Resizing ext4 file system on /dev/mmcblk0p2 ... Model: SD SL08G (sd/mmc)
Disk /dev/mmcblk0: 100%
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Disk Flags:
Nu[ 2.784000] mmcblk0: p1 p2
mber Start End Size Type File system Flags
1 0.05% 0.90% 0.84% primary ext4
2 0.90% 100% 99.1% primary ext4
resize2fs 1.42.13 (17-May-2015)
[ 2.884000] dwc2 c0040000.dwc2otg: EPs: 16, dedicated fifos, 6016 entries in SPRAM
[ 2.992000] dwc2 c0040000.dwc2otg: DWC OTG Controller
[ 2.992000] dwc2 c0040000.dwc2otg: new USB bus registered, assigned bus number 1
[ 2.996000] dwc2 c0040000.dwc2otg: irq 28, io mem 0xc0040000
[ 3.004000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.008000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.016000] usb usb1: Product: DWC OTG Controller
[ 3.020000] usb usb1: Manufacturer: Linux 4.4.49-s5p6818 dwc2_hsotg
[ 3.028000] usb usb1: SerialNumber: c0040000.dwc2otg
[ 3.036000] hub 1-0:1.0: USB hub found
[ 3.036000] hub 1-0:1.0: 1 port detected
[ 3.044000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.048000] ehci-exynos: EHCI EXYNOS driver
[ 3.052000] exynos-ehci c0030000.ehci: EHCI Host Controller
[ 3.056000] exynos-ehci c0030000.ehci: new USB bus registered, assigned bus number 2
[ 3.068000] exynos-ehci c0030000.ehci: irq 27, io mem 0xc0030000
[ 3.084000] exynos-ehci c0030000.ehci: USB 2.0 started, EHCI 1.00
[ 3.084000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.088000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.096000] usb usb2: Product: EHCI Host Controller
[ 3.100000] usb usb2: Manufacturer: Linux 4.4.49-s5p6818 ehci_hcd
[ 3.108000] usb usb2: SerialNumber: c0030000.ehci
[ 3.112000] hub 2-0:1.0: USB hub found
[ 3.116000] hub 2-0:1.0: 3 ports detected
[ 3.120000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.128000] ohci-exynos: OHCI EXYNOS driver
[ 3.132000] exynos-ohci c0020000.ohci: USB Host Controller
[ 3.136000] exynos-ohci c0020000.ohci: new USB bus registered, assigned bus number 3
[ 3.144000] exynos-ohci c0020000.ohci: irq 27, io mem 0xc0020000
[ 3.208000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.208000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.216000] usb usb3: Product: USB Host Controller
[ 3.220000] usb usb3: Manufacturer: Linux 4.4.49-s5p6818 ohci_hcd
[ 3.224000] usb usb3: SerialNumber: c0020000.ohci
[ 3.232000] hub 3-0:1.0: USB hub found
[ 3.232000] hub 3-0:1.0: 3 ports detected
[ 3.240000] usbcore: registered new interface driver uas
[ 3.244000] usbcore: registered new interface driver usb-storage
[ 3.248000] usbcore: registered new interface driver usbserial
[ 3.256000] usbcore: registered new interface driver usbserial_generic
[ 3.260000] usbserial: USB Serial support registered for generic
[ 3.268000] mousedev: PS/2 mouse device common for all mice
[ 3.272000] <<-GTP-INFO->> GTP driver installing
[ 3.280000] himax_ts 2-0048: Unable to get DevId
[ 3.284000] touchscreen-1wire initialized
[ 3.288000] backlight-1wire initialized
[ 3.292000] onewire: REQ 0x60: i2c write error -6
[ 3.296000] input: fa_ts_input as /devices/virtual/input/input0
[ 3.300000] ts-if initialized
[ 3.304000] nx-rtc c0010c00.rtc: [RTC] day=2009.09.01 time=00:00:00
[ 3.312000] nx-rtc c0010c00.rtc: rtc core: registered nx as rtc0
[ 3.316000] i2c /dev entries driver
[ 3.320000] nx-v4l2 nx-v4l2: nx_v4l2_probe success
[ 3.324000] nx-vpu c0080000.video-codec: encoder registered as /dev/video14
[ 3.332000] nx-vpu c0080000.video-codec: decoder registered as /dev/video15
[ 3.348000] c0096000.tmuctrl supply vtmu not found, using dummy regulator
[ 3.348000] thermal thermal_zone0: failed to read out thermal zone (-22)
[ 3.356000] device-mapper: uevent: version 1.0.3
[ 3.360000] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 3.368000] Bluetooth: HCI UART driver ver 2.3
[ 3.372000] Bluetooth: HCI UART protocol H4 registered
[ 3.376000] Bluetooth: HCI UART protocol BCM registered
[ 3.384000] voltage supply : vdd_arm_spu
[ 3.388000] DVFS: ASV[2] IDS 12mA, Ro 112 -> Table [IDS 15mA, Ro 130]
[ 3.392000] ASV 0 = 1400000khz, 1200000 uV
[ 3.396000] ASV 1 = 1300000khz, 1140000 uV
[ 3.400000] ASV 2 = 1200000khz, 1100000 uV
[ 3.404000] ASV 3 = 1100000khz, 1040000 uV
[ 3.408000] ASV 4 = 1000000khz, 1040000 uV
[ 3.416000] ASV 5 = 900000khz, 1000000 uV
[ 3.420000] ASV 6 = 800000khz, 1000000 uV
[ 3.424000] ASV 7 = 700000khz, 980000 uV
[ 3.428000] ASV 8 = 600000khz, 980000 uV
[ 3.432000] ASV 9 = 500000khz, 940000 uV
[ 3.436000] ASV 10 = 400000khz, 940000 uV
[ 3.444000] DVFS: regulator vdd_arm_spu
[ 3.444000] DVFS: cpu DVFS with PLL.1 [tables=11]
[ 3.452000] Synopsys Designware Multimedia Card Interface Driver
[ 3.456000] usbcore: registered new interface driver usbhid
[ 3.460000] usbhid: USB HID core driver
[ 3.464000] ashmem: initialized
[ 3.472000] nexell-pcm nexell-pcm: snd pcm: register sound platform 'nexell-pcm'
[ 3.476000] nexell-i2s c0055000.i2s: snd i2s: ch 0, master, iis mode, 48000(47999)hz, 32 FBITs,
[ 3.484000] nexell-i2s c0055000.i2s: MCLK=12287880hz, RFS=256
[ 3.492000] nexell-spdif-tx c0059000.spdiftx: spdif-tx: 48000(47999)Hz, MCLK=12287880hz
[ 3.500000] nx-simple-card sound: snd-null-voice <-> c0055000.i2s mapping ok
[ 3.504000] nx-simple-card sound: dit-hifi <-> c0059000.spdiftx mapping ok
[ 3.512000] u32 classifier
[ 3.512000] Actions configured
[ 3.516000] Netfilter messages via NETLINK v0.30.
[ 3.520000] nf_conntrack version 0.5.0 (7627 buckets, 30508 max)
[ 3.528000] ctnetlink v0.93: registering with nfnetlink.
[ 3.532000] xt_time: kernel timezone is -0000
[ 3.536000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.544000] arp_tables: (C) 2002 David S. Miller
[ 3.548000] Initializing XFRM netlink socket
[ 3.552000] NET: Registered protocol family 10
[ 3.556000] mip6: Mobile IPv6
[ 3.560000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.564000] NET: Registered protocol family 17
[ 3.568000] NET: Registered protocol family 15
[ 3.572000] Bluetooth: RFCOMM TTY layer initialized
[ 3.576000] Bluetooth: RFCOMM socket layer initialized
[ 3.584000] Bluetooth: RFCOMM ver 1.11
[ 3.588000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.592000] Bluetooth: BNEP filters: protocol multicast
[ 3.596000] Bluetooth: BNEP socket layer initialized
[ 3.604000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.608000] Bluetooth: HIDP socket layer initialized
[ 3.612000] Key type dns_resolver registered
[ 3.620000] Loading compiled-in X.509 certificates
[ 3.624000] input: gpio_keys as /devices/platform/gpio_keys/input/input1
[ 3.628000] nx-rtc c0010c00.rtc: setting system clock to 2009-09-01 00:00:00 UTC (1251763200)
[ 3.644000] dhd_module_init in
[ 3.644000] dhd_wlan_init: START.......
[ 3.644000] failed to get device node of bcmdhd
[ 3.648000] dhd_wlan_init: failed to initiate GPIO, ret=-19
[ 3.656000] dhd_module_init: failed in dhd_wlan_init.
[ 3.660000] ALSA device list:
[ 3.664000] #0: nanopi3-audio
Resizing the filesystem on /dev/mmcblk0p2 to 1923072 (4k) blocks.
The filesystem on /dev/mmcblk0p2 is now 1923072 (4k) blocks long.
done.
[ 3.920000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 4.296000] systemd[1]: System time before build time, advancing clock.
[ 4.380000] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 4.396000] systemd[1]: Detected architecture arm64.
Welcome to Ubuntu core 16.04 LTS!
[ 4.412000] systemd[1]: Set hostname to .
[ 4.416000] random: nonblocking pool is initialized
[ 4.764000] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Audit Socket.
[ 4.784000] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 4.792000] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 4.804000] systemd[1]: Reached target Remote File Systems (Pre).
[ OK ] Reached target Remote File Systems (Pre).
[ 4.820000] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 4.836000] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 4.848000] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ 4.868000] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 4.884000] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 4.896000] systemd[1]: Reached target Encrypted Volumes.
[ OK ] Reached target Encrypted Volumes.
[ 4.908000] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 4.924000] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ 4.944000] systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
[ 4.972000] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 4.984000] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 5.008000] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
[ 5.036000] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 5.060000] systemd[1]: Mounting Huge Pages File System...
Mounting Huge Pages File System...
[ 5.076000] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 5.088000] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 5.108000] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 5.128000] systemd[1]: Starting Set console keymap...
Starting Set console keymap...
[ 5.144000] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 5.164000] systemd[1]: Starting Create list of required static device nodes for the current kernel...
Starting Create list of required st... nodes for the current kernel...
[ 5.188000] systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
[ 5.216000] systemd[1]: Mounted Debug File System.
[ OK ] Mounted Debug File System.
[ 5.228000] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 5.244000] systemd[1]: Mounted Huge Pages File System.
[ OK ] Mounted Huge Pages File System.
[ 5.256000] systemd[1]: Started Load Kernel Modules.
[ OK ] Started Load Kernel Modules.
[ 5.280000] systemd[1]: Started Remount Root and Kernel File Systems.
[ OK ] Started Remount Root and Kernel File Systems.
[ 5.300000] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ OK ] Started Create list of required sta...ce nodes for the current kernel.
[ 5.356000] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Started Set console keymap.
Starting Create Static Device Nodes in /dev...
Starting udev Coldplug all Devices...
Starting Flush Journal to Persistent Storage...
Starting Load/Save Random Seed...
Starting Apply Kernel Variables...
Mounting Configuration File System...
Mounting FUSE Control File System...
[ OK ] Mounted Configuration File System.
[ OK ] Mounted FUSE Control File System.
[ OK ] Started Create Static Device Nodes in /dev.
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Flush Journal to Persistent Storage.
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
Starting Raise network interfaces...
Starting Set console font and keymap...
Starting Create Volatile Files and Directories...
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Synchronized.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting brcm_patchram_plus...
Starting Save/Restore Sound Card State...
Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
Starting dnsmasq - A lightweight DHCP and caching DNS server...
Starting Login Service...
[ OK ] Started D-Bus System Message Bus.
Starting Network Manager...
Starting Modem Manager...
Starting Permit User Sessions...
[ OK ] Started Daily apt activities.
[ OK ] Reached target Timers.
Starting Restore /etc/resolv.conf i...re the ppp link was shut down...
Starting LSB: Start busybox udhcpd at boot time...
[ OK ] Started Set console font and keymap.
[ OK ] Started brcm_patchram_plus.
[ OK ] Started Permit User Sessions.
[ OK ] Started Restore /etc/resolv.conf if...fore the ppp link was shut down.
[ OK ] Started Save/Restore Sound Card State.
[ OK ] Found device /dev/ttySAC0.
[ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
[ OK ] Started LSB: Start busybox udhcpd at boot time.
[ OK ] Started Raise network interfaces.
[ OK ] Started Login Service.
Starting Authenticate and Authorize Users to Run Privileged Tasks...
[ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[ OK ] Reached target Sound Card.
Starting Set console scheme...
[ OK ] Created slice system-getty.slice.
[ OK ] Started Set console scheme.
[ OK ] Started Authenticate and Authorize Users to Run Privileged Tasks.
[ OK ] Started dnsmasq - A lightweight DHCP and caching DNS server.
[ OK ] Started Network Manager.
Starting Network Manager Script Dispatcher Service...
Starting Network Manager Wait Online...
[ OK ] Reached target Network.
Starting OpenBSD Secure Shell server...
[ OK ] Reached target Host and Network Name Lookups.
[ OK ] Started Network Manager Script Dispatcher Service.
[ OK ] Started Modem Manager.
Starting Hostname Service...
[ OK ] Started Hostname Service.
[ OK ] Started OpenBSD Secure Shell server.
[ OK ] Started Network Manager Wait Online.
[ OK ] Reached target Network is Online.
Starting LSB: Advanced IEEE 802.11 management daemon...
Starting LSB: disk temperature monitoring daemon...
Starting /etc/rc.local Compatibility...
Starting LSB: Brings up/down network automatically...
[ OK ] Started LSB: disk temperature monitoring daemon.
[ OK ] Started LSB: Brings up/down network automatically.
[ OK ] Started LSB: Advanced IEEE 802.11 management daemon.
[ 8.361773] rc.local[741]: Setting up swapspace version 1, size = 2 GiB (2147479552 bytes)
[ 8.376213] rc.local[741]: no label, UUID=ec3336bf-1c64-4090-b0f1-da3f6ac32e9b
[ 9.144544] rc.local[741]: vm.swappiness = 10
[ OK ] Started /etc/rc.local Compatibility.
[ OK ] Started Serial Getty on ttySAC0.
[ OK ] Started Getty on tty1.
[ OK ] Reached target Login Prompts.
[ OK ] Reached target Multi-User System.
[ OK ] Reached target Graphical Interface.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Started Update UTMP about System Runlevel Changes.
Ubuntu 16.04.2 LTS NanoPi-Fire3 ttySAC0
Default Login:
Username = pi
Password = pi
NanoPi-Fire3 login: pi (automatic login)
_____ _ _ _ _____ _ _____ ____
| ___| __(_) ___ _ __ __| | |_ _| ____| | | ____/ ___|
| |_ | '__| |/ _ \ '_ \ / _` | | | | | _| | | | _|| |
| _|| | | | __/ | | | (_| | | |_| | |___| |___| |__| |___
|_| |_| |_|\___|_| |_|\__,_|_|\__, |_____|_____|_____\____|
|___/
Welcome to Ubuntu core 16.04 LTS 4.4.49-s5p6818
System load: 0.31 Up time: 11 sec
Memory usage: 4 % of 953Mb IP:
CPU temp: 47°C
Usage of /: 62% of 7.2G
* Documentation: http://wiki.friendlyarm.com/Ubuntu
* Forum: http://www.friendlyarm.com/Forum/
To run Qt5 demo, type "qt5demo" at the command prompt and then hit the enter key.
To play a video demo, use command "sudo gst-player /home/pi/demo.mp4".
To run a command as administrator (user "root"), use "sudo ".
See "man sudo_root" for details.
pi@NanoPi-Fire3:~$
pi@NanoPi-Fire3:~$
pi@NanoPi-Fire3:~$
Have any comments? Questions?
Drop me a line!
Tom's electronics pages / tom@mmto.org